What does BTU stand for?

 

Jacksonville – Duval County: 904-346-1266
St Augustine – St Johns County: 904-824-7144
Orange Park – Clay County: 904-264-6444
Jacksonville Beaches – Duval County: 904-246-3969
Fernandina – Nassau County: 904-277-3040
Macclenny – Baker County: 904-259-5091
Palm Coast – Flagler County: 386-439-5290
Daytona – Volusia County: 386-253-4911
Gainesville – Alachua County: 352-335-8555

Serving all of Florida AND Georgia at: 904-346-1266

E-mail: Larry@1stprop.com (feel free to email your bidding packages here)

The British thermal unit (BTU or Btu) is a traditional unit of energy equal to about 1.06 kilojoules. It is approximately the amount of energy needed to heat one pound of water one degree Fahrenheit. It is used in the power, steam generation, heating and air conditioning industries. In scientific contexts the BTU has largely been replaced by the SI unit of energy, the joule (J), though it may be used as a measure of agricultural energy production (BTU/kg). It is still used unofficially in metric English-speaking countries (such as Canada and the United Kingdom), and remains the standard unit of classification for air conditioning units manufactured and sold in many non-English-speaking metric countries.

In North America, the term “BTU” is used to describe the heat value (energy content) of fuels, and also to describe the power of heating and cooling systems, such as furnaces, stoves, barbecue grills, and air conditioners. When used as a unit of power, BTU per hour (BTU/h) is the correct unit, though this is often abbreviated to just “BTU”.

The unit MBTU was defined as one thousand BTU presumably from the Roman numeral system where “M” stands for one thousand (1,000). This is easily confused with the SI mega (M) prefix, which multiplies by a factor of one million (1,000,000). To avoid confusion many companies and engineers use MMBTU to represent one million BTU. Alternatively a therm is used representing 100,000 or 105 BTU, and a quad as 1015 BTU.

LP Gas piping and repairs, natural gas piping and repairs, appliance repairs, boilers, water heaters, tankless water heaters,  pool heaters, pool pumps, gas generators, medical gas piping, nitrogen gas piping, oxygen gas piping, med gas piping, manometer test, annual gas testing and inspections, splash guards, plumbing, free estimates, licensed and insured.

New construction, alterations, repairs, commercial, industrial, residential, medical, and hospitals…..all work is very welcome and appreciated.

We accept all major credit cards.  Visa, Mastercard, Discover and American Express.

We service the following areas of northeast Florida: Jacksonville, Jacksonville Beach, Atlantic Beach, Neptune Beach, Ponte Vedra Beach, Fernandina, Amelia Island, Callahan, Yulee, Hilliard, Macclenny, St George, St Marys, Kingsland, Orange Park, Middleburg, Green Cove Springs, Penny Farms, St Augustine, Hastings, Palatka, Keystone Heights, Starke, Lake City, Waldo, Baldwin, St Augustine Beach, Crescent Beach, Palm Coast, Daytona, Holly Hill, Titusville, Daytona Shores, Ormond Beach, Bunnell, Deland, Orange City, Port Orange, Orlando, New Smyrna Beach, Sanford, Palm Valley, Fruitcove, Mandarin, Lawtey, St Augustine Beach, Switzerland, Vilano Beach, Marineland, Flagler Beach, Beverly Beach, Sanderson, and Glen St Mary.

State Certified Contractor License Number CFCO56659

NOW HIRING

Apply for a Job online at  www.asapapply.com

CLICK BELOW AND PLACE A WORK ORDER

IN OUR AUTOMATED WORK ORDER SYSTEM

http://www.asap-plumbing.com/Submit_a_New_Work_Order/submit_a_new_work_order.php

ASAP GAS PIPING REPAIRS AND INSTALLATION

is an authorized reseller or service center for many brands:

  • Rinnai/Noritz Tankless Water Heaters
  • Kohler
  • American Standard
  • Rheem
  • A.O. Smith
  • Moen
  • Delta
  • And Many More

Serving the entire Jacksonville area including the following communities:

 
Most people struggle when they want to remodel, so to help out, we have put some hyperlinks to places that will help you decide what type of plumbing fixtures you would like to install. We hope these sites will assist in creating the bathroom of your dreams.  

Click on one of these sites:
Rohlhome.com
Kohler.com
AmericanStandard-US.com
Moen.com
TotoUsa.com
Grohe.com
Tsbrass.com
AOSmith.com
bradfordwhite.com
rinnai.us

 

www.asap-plumbing.com

ASAP Boiler Sales & Repairs

OVER 20 YEARS

serving FLORIDA AND GEORGIA              since 1988

Jacksonville – Duval County: 904-346-1266
St Augustine – St Johns County: 904-824-7144
Orange Park – Clay County: 904-264-6444
Jacksonville Beaches – Duval County: 904-246-3969
Fernandina – Nassau County: 904-277-3040
Macclenny – Baker County: 904-259-5091
Palm Coast – Flagler County: 386-439-5290
Daytona – Volusia County: 386-253-4911
Gainesville – Alachua County: 352-335-8555

Serving all of Florida AND Georgia at: 904-346-1266

E-mail: Larry@1stprop.com (feel free to email your bidding packages here)

LP Gas piping and repairs, natural gas piping and repairs, appliance repairs, boilers, water heaters, tankless water heaters,  pool heaters, pool pumps, gas generators, medical gas piping, nitrogen gas piping, oxygen gas piping, med gas piping, manometer test, annual gas testing and inspections, splash guards, plumbing, free estimates, licensed and insured.

New construction, alterations, repairs, commercial, industrial, residential, medical, and hospitals…..all work is very welcome and appreciated.

We accept all major credit cards.  Visa, Mastercard, Discover and American Express.

We service the following areas of northeast Florida: Jacksonville, Jacksonville Beach, Atlantic Beach, Neptune Beach, Ponte Vedra Beach, Fernandina, Amelia Island, Callahan, Yulee, Hilliard, Macclenny, St George, St Marys, Kingsland, Orange Park, Middleburg, Green Cove Springs, Penny Farms, St Augustine, Hastings, Palatka, Keystone Heights, Starke, Lake City, Waldo, Baldwin, St Augustine Beach, Crescent Beach, Palm Coast, Daytona, Holly Hill, Titusville, Daytona Shores, Ormond Beach, Bunnell, Deland, Orange City, Port Orange, Orlando, New Smyrna Beach, Sanford, Palm Valley, Fruitcove, Mandarin, Lawtey, St Augustine Beach, Switzerland, Vilano Beach, Marineland, Flagler Beach, Beverly Beach, Sanderson, and Glen St Mary.

State Certified Contractor License Number CFCO56659

NOW HIRING

Apply for a Job online at  www.asapapply.com

CLICK BELOW AND PLACE A WORK ORDER

IN OUR AUTOMATED WORK ORDER SYSTEM

http://www.asap-plumbing.com/Submit_a_New_Work_Order/submit_a_new_work_order.php

ASAP GAS PIPING REPAIRS AND INSTALLATION

is an authorized reseller or service center for many brands:

  • Rinnai/Noritz Tankless Water Heaters
  • Kohler
  • American Standard
  • Rheem
  • A.O. Smith
  • Moen
  • Delta
  • And Many More

Serving the entire Jacksonville area including the following communities:

Most people struggle when they want to remodel, so to help out, we have put some hyperlinks to places that will help you decide what type of plumbing fixtures you would like to install. We hope these sites will assist in creating the bathroom of your dreams.  Click on one of these sites:
Rohlhome.com
Kohler.com
AmericanStandard-US.com
Moen.com
TotoUsa.com
Grohe.com
Tsbrass.com
AOSmith.com
bradfordwhite.com
rinnai.us
Deltafaucet.com

Materials

The pressure vessel in a boiler is usually made of steel (or alloy steel), or historically of wrought iron. Stainless steel is virtually prohibited (by the ASME Boiler Code) for use in wetted parts of modern boilers, but is used often in superheater sections that will not be exposed to liquid boiler water. In live steam models, copper or brass is often used because it is more easily fabricated in smaller size boilers. Historically, copper was often used for fireboxes (particularly for steam locomotives), because of its better formability and higher thermal conductivity; however, in more recent times, the high price of copper often makes this an uneconomic choice and cheaper substitutes (such as steel) are used instead.

For much of the Victorian “age of steam”, the only material used for boilermaking was the highest grade of wrought iron, with assembly by rivetting. This iron was often obtained from specialist ironworks, such as at Cleator Moor (UK), noted for the high quality of their rolled plate and its suitability for high-reliability use in critical applications, such as high-pressure boilers. In the 20th century, design practice instead moved towards the use of steel, which is stronger and cheaper, with welded construction, which is quicker and requires less labour.

Cast iron may be used for the heating vessel of domestic water heaters. Although such heaters are usually termed “boilers”, their purpose is usually to produce hot water, not steam, and so they run at low pressure and try to avoid actual boiling. The brittleness of cast iron makes it impractical for high pressure steam boilers.

[edit] Fuel

The source of heat for a boiler is combustion of any of several fuels, such as wood, coal, oil, or natural gas. Electric steam boilers use resistance- or immersion-type heating elements. Nuclear fission is also used as a heat source for generating steam. Heat recovery steam generators (HRSGs) use the heat rejected from other processes such as gas turbines.

[edit] Configurations

Boilers can be classified into the following configurations:

  • “Pot boiler” or “Haycock boiler”: a primitive “kettle” where a fire heats a partially-filled water container from below. 18th century Haycock boilers generally produced and stored large volumes of very low-pressure steam, often hardly above that of the atmosphere. These could burn wood or most often, coal. Efficiency was very low.
  • Fire-tube boiler. Here, water partially fills a boiler barrel with a small volume left above to accommodate the steam (steam space). This is the type of boiler used in nearly all steam locomotives. The heat source is inside a furnace or firebox that has to be kept permanently surrounded by the water in order to maintain the temperature of the heating surface just below boiling point. The furnace can be situated at one end of a fire-tube which lengthens the path of the hot gases, thus augmenting the heating surface which can be further increased by making the gases reverse direction through a second parallel tube or a bundle of multiple tubes (two-pass or return flue boiler); alternatively the gases may be taken along the sides and then beneath the boiler through flues (3-pass boiler). In the case of a locomotive-type boiler, a boiler barrel extends from the firebox and the hot gases pass through a bundle of fire tubes inside the barrel which greatly increase the heating surface compared to a single tube and further improve heat transfer. Fire-tube boilers usually have a comparatively low rate of steam production, but high steam storage capacity. Fire-tube boilers mostly burn solid fuels, but are readily adaptable to those of the liquid or gas variety.
  • Water-tube boiler. In this type,the water tubes are arranged inside a furnace in a number of possible configurations: often the water tubes connect large drums, the lower ones containing water and the upper ones, steam and water; in other cases, such as a monotube boiler, water is circulated by a pump through a succession of coils. This type generally gives high steam production rates, but less storage capacity than the above. Water tube boilers can be designed to exploit any heat source and are generally preferred in high pressure applications since the high pressure water/steam is contained within small diameter pipes which can withstand the pressure with a thinner wall.
  • Fire-tube boiler with Water-tube firebox. Sometimes the two above types have been combined in the following manner: the firebox contains an assembly of water tubes, called thermic syphons. The gases then pass through a conventional firetube boiler. Water-tube fireboxes were installed in many Hungarian locomotives, but have met with little success in other countries.
  • Sectional boiler. In a cast iron sectional boiler, sometimes called a “pork chop boiler” the water is contained inside cast iron sections. These sections are assembled on site to create the finished boiler.
  • [edit] Safety

    Historically, boilers were a source of many serious injuries and property destruction due to poorly understood engineering principles. Thin and brittle metal shells can rupture, while poorly welded or riveted seams could open up, leading to a violent eruption of the pressurized steam. Collapsed or dislodged boiler tubes could also spray scalding-hot steam and smoke out of the air intake and firing chute, injuring the firemen who loaded coal into the fire chamber. Extremely large boilers providing hundreds of horsepower to operate factories could demolish entire buildings.[4]

    A boiler that has a loss of feed water and is permitted to boil dry can be extremely dangerous. If feed water is then sent into the empty boiler, the small cascade of incoming water instantly boils on contact with the superheated metal shell and leads to a violent explosion that cannot be controlled even by safety steam valves. Draining of the boiler could also occur if a leak occurred in the steam supply lines that was larger than the make-up water supply could replace. The Hartford Loop was invented in 1919 by the Hartford Steam Boiler and Insurance Company as a method to help prevent this condition from occurring, and thereby reduce their insurance claims.[5]

    Most boilers heat water until it boils, and then the steam is used at saturation temperature (i.e., saturated steam). Superheated steam boilers boil the water and then further heat the steam in a superheater. This provides steam at much higher temperature, but can decrease the overall thermal efficiency of the steam generating plant due to the fact that the higher steam temperature requires a higher flue gas exhaust temperature. There are several ways to circumvent this problem, typically by providing a feedwater heating “ecomomizer”, and/or a combustion air heater in the hot flue gas exhaust path. There are advantages to superheated steam and this may (and usually will) increase overall efficiency of both steam generation and its utilisation considered together: gains in input temperature to a turbine should outweigh any cost in additional boiler complication and expense. There may also be practical limitations in using “wet” steam, as causing condensation droplets will damage turbine blades.

    Superheated steam presents unique safety concerns because, if there is a leak in the steam piping, steam at such high pressure/temperature can cause serious, instantaneous harm to anyone entering its flow. Since the escaping steam will initially be completely superheated vapor, it is not easy to see the leak, although the intense heat and sound from such a leak clearly indicates its presence.

    The superheater works like coils on an air conditioning unit, however to a different end. The steam piping (with steam flowing through it) is directed through the flue gas path in the boiler furnace. This area typically is between 1,300–1,600 degree Celsius (2,372–2,912 °F). Some superheaters are radiant type (absorb heat by radiation), others are convection type (absorb heat via a fluid i.e. gas) and some are a combination of the two. So whether by convection or radiation the extreme heat in the boiler furnace/flue gas path will also heat the superheater steam piping and the steam within as well. It is important to note that while the temperature of the steam in the superheater is raised, the pressure of the steam is not: the turbine or moving pistons offer a “continuously expanding space” and the pressure remains the same as that of the boiler.[6] The process of superheating steam is most importantly designed to remove all droplets entrained in the steam to prevent damage to the turbine blading and/or associated piping.

    [edit] Supercritical steam generators

    Supercritical steam generators (also known as Benson boilers) are frequently used for the production of electric power. They operate at “supercritical pressure”. In contrast to a “subcritical boiler”, a supercritical steam generator operates at such a high pressure (over 3,200 psi/22.06 MPa or 220.6 bar) that actual boiling ceases to occur, and the boiler has no water – steam separation. There is no generation of steam bubbles within the water, because the pressure is above the “critical pressure” at which steam bubbles can form. It passes below the critical point as it does work in the high pressure turbine and enters the generator’s condenser. This is more efficient, resulting in slightly less fuel use. The term “boiler” should not be used for a supercritical pressure steam generator, as no “boiling” actually occurs in this device.

    [edit] History of supercritical steam generation

    Contemporary supercritical steam generators are sometimes referred as Benson boilers. In 1922, Mark Benson was granted a patent for a boiler designed to convert water into steam at high pressure.

    Safety was the main concern behind Benson’s concept. Earlier steam generators were designed for relatively low pressures of up to about 100 bar (10,000 kPa; 1,450 psi), corresponding to the state of the art in steam turbine development at the time. One of their distinguishing technical characteristics was the riveted drum. These drums were used to separate water and steam, and were often the source of boiler explosions, usually with catastrophic consequences. However, the drum can be completely eliminated if the evaporation process is avoided altogether. This happens when water is heated at a pressure above the critical pressure and then expanded to dry steam at subcritical pressure. A throttle valve located downstream of the evaporator can be used for this purpose.

    As development of Benson technology continued, boiler design soon moved away from the original concept introduced by Mark Benson. In 1929, a test boiler that had been built in 1927 began operating in the thermal power plant at Gartenfeld in Berlin for the first time in subcritical mode with a fully open throttle valve. The second Benson boiler began operation in 1930 without a pressurizing valve at pressures between 40 and 180 bar (4,000 and 18,000 kPa; 580 and 2,611 psi) at the Berlin cable factory. This application represented the birth of the modern variable-pressure Benson boiler. After that development, the original patent was no longer used. The Benson boiler name, however, was retained.

    Two current innovations have a good chance of winning acceptance in the competitive market for once-through steam generators:

    • A new type of heat-recovery steam generator based on the Benson boiler, which has operated successfully at the Cottam combined-cycle power plant in the central part of England,
    • The vertical tubing in the combustion chamber walls of coal-fired steam generators which combines the operating advantages of the Benson system with the design advantages of the drum-type boiler. Construction of a first reference plant, the Yaomeng power plant in China, commenced in 2001.

    [edit] Hydronic boilers

    Hydronic boilers are used in generating heat for residential and industrial purposes. They are the typical power plant for central heating systems fitted to houses in northern Europe (where they are commonly combined with domestic water heating), as opposed to the forced-air furnaces or wood burning stoves more common in North America. The hydronic boiler operates by way of heating water/fluid to a preset temperature (or sometimes in the case of single pipe systems, until it boils and turns to steam) and circulating that fluid throughout the home typically by way of radiators, baseboard heaters or through the floors. The fluid can be heated by any means…gas, wood, fuel oil, etc, but in built-up areas where piped gas is available, natural gas is currently the most economical and therefore the usual choice. The fluid is in an enclosed system and circulated throughout by means of a motorized pump. The name “boiler” can be a misnomer in that, except for systems using steam radiators, the water in a properly functioning hydronic boiler never actually boils. Most new systems are fitted with condensing boilers for greater efficiency. These boilers are referred to as condensing boilers because they condense the water vapor in the flue gases to capture the latent heat of vaporization of the water produced during combustion.

    Hydronic systems are being used more and more in new construction in North America for several reasons. Among the reasons are:

    • They are more efficient and more economical than forced-air systems (although initial installation can be more expensive, because of the cost of the copper and aluminum).
    • The baseboard copper pipes and aluminum fins take up less room and use less metal than the bulky steel ductwork required for forced-air systems.
    • They provide more even, less fluctuating temperatures than forced-air systems. The copper baseboard pipes hold and release heat over a longer period of time than air does, so the furnace does not have to switch off and on as much. (Copper heats mostly through conduction and radiation, whereas forced-air heats mostly through forced convection. Air has much lower thermal conductivity and volumetric heat capacity than copper, so the conditioned space warms up and cools down more quickly than with hydronic. See also thermal mass.)
    • They do not dry out the interior air as much.
    • They do not introduce any dust, allergens, mold, or (in the case of a faulty heat exchanger) combustion byproducts into the living space.

    Forced-air heating does have some advantages, however. See forced-air heating.

    [edit] Accessories

    [edit] Boiler fittings and accessories

    • Safety valve: It is used to relieve pressure and prevent possible explosion of a boiler.
    • Water level indicators: They show the operator the level of fluid in the boiler, also known as a sight glass, water gauge or water column is provided.
    • Bottom blowdown valves: They provide a means for removing solid particulates that condense and lay on the bottom of a boiler. As the name implies, this valve is usually located directly on the bottom of the boiler, and is occasionally opened to use the pressure in the boiler to push these particulates out.
    • Continuous blowdown valve: This allows a small quantity of water to escape continuously. Its purpose is to prevent the water in the boiler becoming saturated with dissolved salts. Saturation would lead to foaming and cause water droplets to be carried over with the steam – a condition known as priming. Blowdown is also often used to monitor the chemistry of the boiler water.
    • Flash Tank: High pressure blowdown enters this vessel where the steam can ‘flash’ safely and be used in a low-pressure system or be vented to atmosphere while the ambient pressure blowdown flows to drain.
    • Automatic Blowdown/Continuous Heat Recovery System: This system allows the boiler to blowdown only when makeup water is flowing to the boiler, thereby transferring the maximum amount of heat possible from the blowdown to the makeup water. No flash tank is generally needed as the blowdown discharged is close to the temperature of the makeup water.
    • Hand holes: They are steel plates installed in openings in “header” to allow for inspections & installation of tubes and inspection of internal surfaces.
    • Steam drum internals, A series of screen, scrubber & cans (cyclone separators).
    • Low- water cutoff: It is a mechanical means (usually a float switch) that is used to turn off the burner or shut off fuel to the boiler to prevent it from running once the water goes below a certain point. If a boiler is “dry-fired” (burned without water in it) it can cause rupture or catastrophic failure.
    • Surface blowdown line: It provides a means for removing foam or other lightweight non-condensible substances that tend to float on top of the water inside the boiler.
    • Circulating pump: It is designed to circulate water back to the boiler after it has expelled some of its heat.
    • Feedwater check valve or clack valve: A non-return stop valve in the feedwater line. This may be fitted to the side of the boiler, just below the water level, or to the top of the boiler.
    • Top feed: A check valve (clack valve) in the feedwater line, mounted on top of the boiler. It is intended to reduce the nuisance of limescale. It does not prevent limescale formation but causes the limescale to be precipitated in a powdery form which is easily washed out of the boiler.
    • Desuperheater tubes or bundles: A series of tubes or bundles of tubes in the water drum or the steam drum designed to cool superheated steam. Thus is to supply auxiliary equipment that doesn’t need, or may be damaged by, dry steam.
    • Chemical injection line: A connection to add chemicals for controlling feedwater pH.

    [edit] Steam accessories

    • Main steam stop valve:
    • Steam traps:
    • Main steam stop/Check valve: It is used on multiple boiler installations.

    [edit] Combustion accessories

    • Fuel oil system:
    • Gas system:
    • Coal system:
    • Soot blower

    [edit] Other essential items

    [edit] Controlling draft

    Most boilers now depend on mechanical draft equipment rather than natural draft. This is because natural draft is subject to outside air conditions and temperature of flue gases leaving the furnace, as well as the chimney height. All these factors make proper draft hard to attain and therefore make mechanical draft equipment much more economical.

    There are three types of mechanical draft:

    • Induced draft: This is obtained one of three ways, the first being the “stack effect” of a heated chimney, in which the flue gas is less dense than the ambient air surrounding the boiler. The denser column of ambient air forces combustion air into and through the boiler. The second method is through use of a steam jet. The steam jet oriented in the direction of flue gas flow induces flue gasses into the stack and allows for a greater flue gas velocity increasing the overall draft in the furnace. This method was common on steam driven locomotives which could not have tall chimneys. The third method is by simply using an induced draft fan (ID fan) which removes flue gases from the furnace and forces the exhaust gas up the stack. Almost all induced draft furnaces operate with a slightly negative pressure.
    • Forced draft: Draft is obtained by forcing air into the furnace by means of a fan (FD fan) and ductwork. Air is often passed through an air heater; which, as the name suggests, heats the air going into the furnace in order to increase the overall efficiency of the boiler. Dampers are used to control the quantity of air admitted to the furnace. Forced draft furnaces usually have a positive pressure.
    • Balanced draft: Balanced draft is obtained through use of both induced and forced draft. This is more common with larger boilers where the flue gases have to travel a long distance through many boiler passes. The induced draft fan works in conjunction with the forced draft fan allowing the furnace pressure to be maintained slightly below atmospheric.

    The British thermal unit (BTU or Btu) is a traditional unit of energy equal to about 1.06 kilojoules. It is approximately the amount of energy needed to heat one pound of water one degree Fahrenheit. It is used in the power, steam generation, heating and air conditioning industries. In scientific contexts the BTU has largely been replaced by the SI unit of energy, the joule (J), though it may be used as a measure of agricultural energy production (BTU/kg). It is still used unofficially in metric English-speaking countries (such as Canada and the United Kingdom), and remains the standard unit of classification for air conditioning units manufactured and sold in many non-English-speaking metric countries.

    In North America, the term “BTU” is used to describe the heat value (energy content) of fuels, and also to describe the power of heating and cooling systems, such as furnaces, stoves, barbecue grills, and air conditioners. When used as a unit of power, BTU per hour (BTU/h) is the correct unit, though this is often abbreviated to just “BTU”.

    The unit MBTU was defined as one thousand BTU presumably from the Roman numeral system where “M” stands for one thousand (1,000). This is easily confused with the SI mega (M) prefix, which multiplies by a factor of one million (1,000,000). To avoid confusion many companies and engineers use MMBTU to represent one million BTU. Alternatively a therm is used representing 100,000 or 105 BTU, and a quad as 1015 BTU.

    BERNIE WILSON

    ATLANTIC BEACH

    HYDROCHEMOCHAL

    WELDING

    MAINTENANCE

    BOILER

    FURNACE

    SERVICE

    YAWN FLEA MARKETT

    CLEANING

    YOWN

    CERTIFIED

    TURNER

    ALLEN

    REPAIR

    SERVICE

    INSPECTION

    INSPECTING

    BROS

    BROTHERS

    ROWE AND MARTIN

    AND

    WHOLESALE

    METRO SAND CLEANING

    ENGINEERING

    ROOTER CLEANING

    DAVID

    MARINE

    WALASHEK MARKETING

    TERRY SMOOTH

    EXPERT

    SUNSHINE

    HEATING

    A/C

    AIR CONDITIONING

    ILLINGWORTH

    SALES

    FLORIDA

    GRAY

    GREY

    ROOTER CLEANING

    INDUSTRIAL

    FIREBRICK

    BERNIE

    WATER HEATER

    STEAM

    SOLAR

    DARLEY

    PARTS

    BOILER PARTS

    BOILER REPAIRS

    BOILER SERVICE

    ROLLANDING

    WARRANTY

    WARRANTIES

    STATE

    WELDER

    BOILER HAULOFF

    FREE ESTIMATES

    STEAM ENGINE

    BILL

    PLUMBING

    TURBO

    STEAM GENERATOR

    STEAM PISTON

    STEAM WHISTLE

    COMFORTEE

    FENWICKEE

    MR

    DR

    MRS

    MISS

    VEREENEE

    PHILIP

    RONNIE

    CRAFT

    TURNER PASTE

    REASH PASTE

    NORMAN

    EARL

    DAVID

    PLUMBING

    DYNAMIC

    GATORISTIC

    PACKED

    PACETTI FARMS

    TIM WILLIAMS

    MASTER

    LOPEZ HUNTING LODGE

    DAN MIKEL

    1

    2

    3

    4

    5

    6

    PAUL JENKINSS

    SAPP SUCKER

    JOHN NEW WAVE

    DICKIE ALWORTH GREEN

    BOYETTE SMITH

    JAX TANK

    SEPTIC

    MIKE BETROS

    CARVER JENKINS

    DUNNING SMITHE

    PAT EVANS JENKINS

    DAVEY CROCKETT

    FILO  EAGERTON HARRIS

    DON CRABTREE

    GREG MCKENDREE

    GREG DOWLING

    KIMBALL TURNER

    WARD FAULKNER

    GORMAN DOWLING

    ABLE AND WILLING

    RAY TOUCHTON

    GENE BRADSHAW

    STEVE MORTON

    PUMP

    FLORIDA

    ECO

    IRRIGATION

    PIPE

    PARTS

    CITY

    QUICK DISCONNECT

    ALL

    ADI

    MARK HAMM

    DON HILL

    HARRY GATEWAY

    ALL WATER

    GREY WATER KWIK

    GRAY WATER

    WEEK WATER

    LEAK DETECTION

    FIX

    GAS

    LP

    Z

    Southwest County Road

    NATURAL

    KWICK

    UNITED STATES

    AFFORDABLE PRICES

    BROWN WATER

    A

    G

    B

    &

    AND

    MIKE NEDDEL

    TO

    BALDWIN FLORIDA

    DISPATCH

    AA

    AAA

    AAAA

    A

    JOHN W RODGERS

    GARY R BITTLES

    ON A BUDGET

    GARY CONN

    STANDARD SCOTT

    HAYES

    JD

    EASTER

    EASTERDAY

    XMAS DAY

    CELTIC HOLIDAYS

    RAPID

    NOW HIRING IN FLORIDA

    SPECIALIST IN IRRIGATION

    DOLPHIN SITINGS

    DREW SANVILLE

    MIKE SHORE

    NORTH

    SOUTH

    EAST WEST

    TROY ARKO

    PREMIERE

    LEON STARKE VAUGHN

    MAIN

    ROAD AND WOOD

    STREET

    AMERICAN

    NORTH AMERICAN

    FIRST COAST

    SOUTH AMERICAN

    DALE SMITH

    CROCKER ALLEN

    ON CALL MASTER

    FOUR

    WATER HEATER

    DAVID WOOD

    C

    A

    M M

    T

    W

    DOLLAR STAR

    SKIP WATSON

    PLUMBING

    H2O

    WATER

    HYDROGEN

    GENE SASSAMAN

    NOW

    REENE BALLEW

    other websites we recommend you look at

    www.asap-plumbing.com

    www.asapgasinstallers.com

    www.dirtandsandforsale.com

    www.asaproofinspections.com

    http://allprogas.com/

    http://asapbackflowtesting.com/

    http://allproplumbing.us/

    http://asapirrigation.us/